需要金幣： 1000 個金幣 |
資料包括：完整論文 |  |
 |
| 轉換比率：金額 X 10=金幣數量， 例100元=1000金幣 | 論文字?jǐn)?shù)：14193 |  | |
| 折扣與優惠：團購最低可5折優惠 - 了解詳情 | 論文格式：Word格式(*.doc) |  |
摘要：通過雙螺桿擠出機擠出自制的聚丙烯原料，擠出的料直接進入自制的浸漬設備，同時把玻纖通入自制的浸漬設備，使玻纖充分熔融浸漬，初步得到連續玻纖增強聚丙烯片材。然后將所得片材通過平板硫化機層壓得到連續玻纖增強聚丙烯片材。力學性能測試結果表明：隨著PP-g-MAH用量的增加，玻纖片材的拉伸強度呈上升趨勢，斷裂伸長率并沒有明顯變化。隨著相容劑PP-g-MAH用量的增加彎曲強度呈上升趨勢，到達一定值時，彎曲強度變化不大。玻纖的加入使得聚丙烯的拉伸強度迅速提高，玻纖含量的增加，片材的拉伸強度是先增大后降低。斷裂伸長率在加入玻纖后迅速降低，隨著玻纖含量的變化，連續片材斷裂伸長率變化不大。彎曲強度隨著玻纖的加入后明顯提高，當玻纖含量到達一定程度時，彎曲強度有所下降。 關鍵詞：熔融浸漬；連續玻纖；聚丙烯；力學性能
Abstract：Polypropylene materials ,the extrusion of material directly put into a homemade dipping equipment, are extruded through the twin-screw extruder.At the same time, we put the fiberglass into the homemade dipping equipment to make the fiberglass full melt impregnation. We can get the initial continuous glass fiber reinforced polypropylene sheets. And then make the sheets by vulcanizing machine laminating to get the continuous glass fiber reinforced polypropylene sheets. The mechanical properties of the test results show that: With the increase in the amount of PP-g-MAH , the tensile strength of glass fiber sheet shows upward trend, the elongation at break did not change significantly. With the amount of compatilizer of PP-g-MAH was increased, the flexural strength shows upward trend ,when reached a certain value, the bending strength changed little. With the attend of fiber glass ,the tensile strength of polypropylene is rapidly increasing. With the increase of glass content, the tensile strength of the sheet is first increased and then decreased. Elongation at break decreased rapidly after the attend of the fiber glass .With the changes of the content of glass fiber ,the continuous sheet’s elongation at break changed little. With the accession of the glass fiber, the flexural strength significantly improved, when the glass content reaches a certain level, the bending strength has declined.Key words: melt impregnation; continuous glass; polypropylene; mechanical properties.
|
